ANALISIS PUTARAN DRILL BITS BERDASARKAN DIAMETER TERHADAP WAKTU DAN BIAYA PENGERJAAN PADA MESIN BOR FIRST LC-25A
ANALYSIS OF DRILL BITS ROTATION BASED ON DIAMETER ON TIME AND COST OF OPERATION IN FIRST LC-25A DRILL MACHINE
Proses permesinan pada era industri 4.0 semakin berkembang pesat seiring berjalannya waktu, terutama pada kegiatan produksi yang harus berjalan dengan kualitas yang baik serta waktu yang efisien. Penyelesaian pekerjaan konstruksi khususnya pada mesin bor (drilling machine) menjadi proses permesinan dasar yang akan mempengaruhi proses permesinan selanjutnya. Lama waktu pengerjaan pada proses permesinan mempengaruhi hubungan terhadap biaya pengerjaan yang dapat menurunkan produktifitas permesinan. Salah satu mesin bor (drill) pada bengkel Mandiri Raya Teknik adalah Mesin Bor Vertikal First LC-25A dan telah lama tidak difungsikan, perlu adanya referensi dari kinerja dari pengeboran mesin ini. Tujuan dari penilitian ini adalah menentukan pengaruh diameter mata bor, kecepatan spindel, dan material terhadap waktu dan biaya pengerjaan.
Jenis penelitian tugas akhir ini adalah penelitian eksperimen dan analisis data yang digunakan adalah analisis deksriptif dengan mesin bor yang digunakan adalah mesin bor tipe First LC-25A, tiga diameter mata bor HSS yaitu 5mm, 7,5mm dan 10mm, dan material benda uji Baja ST 37, Baja ST 40, dan Aluminium 5356, serta kecepatan spindel yang digunakan adalah 1372,6 rpm, 1050,5 rpm, dan 518,5 rpm.
Dari hasil penelitian ini didapatkan waktu rata-rata pengeboran tercepat pada diameter mata bor 5 mm dan kecepatan spindel 1372,6 rpm untuk masing-masing material ST 37, ST 40 , dan Al 5356 sebesar sebesar 54,3 detik, 96,3 detik, dan 25 detik, kemudian untuk waktu rata-rata terlama adalah pada kecepatan putaran 518,5 rpm dengan diameter 10 mm pada masing-masing pengeboran material benda kerja ST 37, ST 40, dan Al 5356 sebesar 150 detik, 218 detik, dan 94,6 detik. Waktu hasil pengeboran dengan material jenis Aluminium 5356 memiliki waktu rata-rata pengerjaan yang lebih cepat dibandingkan dengan material jenis Baja ST 37 dan ST 40 dengan nilai waktu rata-rata pengujian tercepat pada Aluminium 5356 sebesar 25 detik dan waktu rata-rata pengujian terlama pada baja ST yaitu ST 40 dengan nilai 218 detik. Biaya pengerjaan yang ekonomis pada mesin bor First LC-25A untuk material Aluminium 5356 adalah sebesar Rp127, sedangkan biaya pengerjaan yang ekonomis untuk material jenis Baja ST 37 dan ST 40 adalah Rp272 dan Rp483.
Machining processes in the era of Industry 4.0 are rapidly advancing over time, especially in production activities that require good quality and efficient time management. The completion of construction work, particularly in drilling machines, is a fundamental machining process that influences subsequent machining processes. The duration of machining processes affects the cost of work, which can decrease machining productivity. One of the drilling machines at Mandiri Raya Teknik workshop is the First LC-25A Vertical Drilling Machine, which has not been in use for a long time. Therefore, it is necessary to reference the performance of this drilling machine. The aim of this research is to determine the influence of drill bit diameter, spindle speed, and material on the machining time and cost.
This final project research is an experimental study, and the data analysis used is descriptive analysis. The drilling machine used is the First LC-25A type, with three HSS drill bit diameters: 5mm, 7.5mm, and 10mm. The test materials used are ST 37 Steel, ST 40 Steel, and Aluminum 5356, with spindle speeds of 1372.6 rpm, 1050.5 rpm, and 518.5 rpm, respectively.
From the results of this research, the fastest average drilling time was obtained with a 5mm drill bit diameter and a spindle speed of 1372.6 rpm for each material (ST 37, ST 40, and Al 5356), which were 54.3 seconds, 96.3 seconds, and 25 seconds, respectively. The longest average drilling time was recorded at a spindle speed of 518.5 rpm with a 10mm diameter for each material (ST 37, ST 40, and Al 5356), which were 150 seconds, 218 seconds, and 94.6 seconds, respectively. The drilling time for Aluminum 5356 was found to be faster on average compared to ST 37 and ST 40, with the fastest average testing time for Aluminum 5356 being 25 seconds, while the longest average testing time was recorded for ST 40 at 218 seconds. The economical cost of work on the First LC-25A drilling machine for Aluminum 5356 material is Rp127, while the economical cost for ST 37 and ST 40 Steel materials is Rp272 and Rp483, respectively.