RANCANG BANGUN BATERAI CHARGER MOBIL DENGAN PENGISIAN CEPAT SYSTEM CUT-OFF
DESIGN OF CHARGER BATTERY WITH FAST CHARGING SYSTEM CUT–OFF
ABSTRAK
Nama : Muhammad Jazuli Asfan
NIM : 16050423028
Program Studi : D3 Teknik Mesin
Konsentrasi : Otomotif
Jurusan : Teknik Mesin
Nama Lembaga : Universitas Negeri Surabaya
Pembimbing : Dr. I Made Arsana, S.Pd., M.T.
Energi listrik saat ini sangat dibutuhkan pada semua aspek kehidupan, terutama pada sistem elektronika dan instrumen kendaraan bermotor. Baterai merupakan salah satu energi listrik yang sangat banyak digunakan oleh kendaraan bermotor. Perkembangan baterai pada saat ini dapat ditemukan dalam bentuk yang bervariasi dan memiliki bentuk maupun kapasitas penyimpanan yang besar, diantaranya adalah Aki. Aki sama seperti baterai lainya jika lama digunakan dengan sendirinya akan mengalami penurunan muatan listrik, dengan pengisian/charger aki akan tetap mempunyai muatan listrik. Pengisian baterai dengan charger aki yang efisien dan tidak terlalu penuh atau overcharger dapat bekerja secara otomatis. Berdasarkan Permasalahan yang terjadi pada alat charger adalah alat charger dengan waktu pengisian yang lama serta tidak dilengkapi dengan komponen tambahan untuk memutuskan atau menstabilkan aliran tegangan yang menuju ke aki, sehingga aki overcharger atau bisa merusak aki tersebut.
Berdasarkan hal tersebut maka mendorong penulis membuat alat charger aki pengisian cepat di lengkapi dengan system cut-off. Untuk mencapai dalam pembuatan alat charger aki, maka penelitian menggunakan metode R&D (Research and Development) yaitu penelitian pengembangan berbasis eksperimen. Mengacu pada penentuan spesifikasi komponen, jenis komponen yang akan digunakan pada alat charger baterai aki dilengkapi pemutus arus otomatis.
Hasil akhir dari rancangan ini adalah terciptanya alat charger aki mobil pengisian cepat system cut-off dengan spesifikasi box charger berukuran panjang 40 cm x lebar 25 cm x tinggi 25 cm. Bahan yang dipilih adalah plat besi dengan ketebalan 2 mm, penampang komponen Mika Akrilik ketebalan 5 mm, serta komponen dengan power supply Output 19 V DC, Step-Down (13,5 V) 5 A konfigurasi pemakaian, charger control dengan system cut-off pada tegangan 13,3 V untuk pemutusan laju aliran arus, serta power analyzer untuk melihat arus dan tegangan yang dialirkan maupun yang terdapat pada baterai. Alat ini dapat bekerja secara produktivitas dan efektivitas dalam proses pengisian aki mobil selama 5 jam pengisian dengan aki kapasitas 35 Ah 12 Volt dan juga untuk media pembelajaran di Laboratorium Perpindahan Panas Teknik Mesin Unesa.
Kata Kunci: Baterai Charger mobil, Charger Accu Otomatis, Aki
ABSTRACT
Name : Muhammad Jazuli Asfan
ID Number : 16050423028
Study Program : Diploma III in Mechanical Engineering
Department : Mechanical Engineering
Concentration : Automotive
Name of Institution : University State Of Surabaya
Advisor : Dr. I Made Arsana S.Pd., M.T.
Electrical energy is currently needed in all aspects of life, especially in electronic systems and motor vehicle instruments. The battery is one of the electrical energy that is very widely used by motorized vehicles. The development of batteries at this time can be found in various forms and has a large form and storage capacity, including the battery. The battery is the same as any other battery if it is used for a long time, it will automatically experience a decrease in electric charge, by charging / charger the battery will still have an electric charge. Charging the battery with an efficient battery charger and not too full or the overcharger can work automatically. Based on the problems that occur with the charger, it is a charger device with a long charging time and is not equipped with additional components to disconnect or stabilize the voltage flow leading to the battery, so that the battery overcharges or can damage the battery.
Based on this, it encourages the author to make a fast-charging battery charger device equipped with a cut-off system. To achieve this in the manufacture of a battery charger device, research uses the R&D (Research and Development) method, namely experimental-based development research. Referring to the determination of component specifications, the types of components to be used in the battery charger device are equipped with an automatic circuit breaker.
The final result of this design is the creation of a car battery charger tool fast charging cut-off system with a charger box specification measuring 40 cm long x 25 cm wide x 25 cm high. The material chosen is an iron plate with a thickness of 2 mm, a cross-section of the Mica Acrylic component with a thickness of 5 mm, as well as a component with a 19 V DC output power supply, Step-Down (13.5 V) 5 A usage configuration, charger control with a cut-off system. at a voltage of 13.3 V for termination of the current flow rate, as well as a power analyzer to see the current and voltage flowed or contained in the battery. This tool can work productivity and effectiveness in the process of charging a car battery for 5 hours of charging with a 35 Ah 12 Volt battery and also for learning media at the Unesa Mechanical Engineering Heat Transfer Laboratory.
Keyword: Car Battery Chargers, Auto Accu Chargers, Batteries