RANCANG BANGUN ALAT UJI BENDING DENGAN SISTEM HIDROLIK
DESIGN AND BUILD BENDING TEST EQUIPMENT WITH A HYDRAULIC SYSTEM
ABSTRAK
Nama : Fahrizal Muhammad Fais
NIM : 17050423010
Program Studi : D3 Teknik Mesin
Jurusan : Teknik Mesin
Fakultas : Teknik
Nama Lembaga : Universitas Negeri Surabaya
Pembimbing : Tri Hartutuk Ningsih, S.T., M.T.
Pentingnya pengujian bending untuk mengetahui kemampuan sifat mekanik dari bahan, terutama bahan baja hasil pengelasan, untuk mengetahui kelenturan bahan dan kekuatan bahan uji. Pengujian bending banyak dilakukan untuk menguji kemampuan tekuk material hasil pengelasan. Pada matakuliah ilmu bahan dan di laboratorium ilmu bahan belum adanya alat peraga praktikum dan pengujian bending. Oleh sebab itu alat uji bending ini dibuat sangat aman untuk peraga praktikum dan pengujian di laboratorium.
Uji lengkung (bending test) merupakan salah satu jenis pengujian bahan yang dilakukan untuk mengetahui sifat mekanik suatu bahan teknik. Dalam prakteknya masih sedikit praktisi pengujian bahan yang memperhatikan aspek pengaruh variasi benda uji terhadap data hasil uji bending, dan dimensi yang sudah ada pada standart ASTM E855-08 yang kami gunakan. Untuk itu alat uji bending ini dibuat untuk mempelajari pengaruh variasi dimensi benda uji pada pengujian lengkung. Pengujian dilakukan dengan menggunakan alat uji bending sistem hidrolik. Dengan metode penelitian yang digunakan adalah three point bending, yang mana alat pada penelitian ini merupakan alat yang dimodifikasi dari alat yang sudah ada. Modifikasi alat ini dilakukan pada bagian manometer untuk tekanan hidrolik, penekan bahan uji, dan juga tumpangan spesimen. Dan pengujian terhadap bahan uji baja S45C satu variasi dimensi dengan tiga kali percobaan yaitu dengan ukuran 400x40mm dan memiliki ketebalan 5mm sedangkan metode yang digunakan dalam pengujian ini adalah three point bending.
Data tekanan dongkrak, simpangan dan waktu diambil hingga spesimen/benda uji mendapatkan tekanan maksimal dan gaya tekan hidrolik. Hasil pengujian menunjukan bahwa dimensi benda uji mempengaruhi gaya tekan yang terjadi pada saat pengujian. Semakin besar dimensi yang diuji maka semakin besar juga gaya tekan yang ditimbulkan. Pada saat melakukan bending test nilai rata-rata flexural strength yang didapatkan dengan menggunakan metode three point bending untuk baja tebal 5mm sebesar 213,5 Mpa, pengujian kedua 228 Mpa, dan pada pengujian yang ketiga mendapati hasil 232,1 Mpa.
Kata Kunci: Bending Test, Dimensi, Flexural Strength, Three Point Bending
ABSTRACT
Name : Fahrizal Muhammad Fais
The importance of bending testing is to determine the ability of the mechanical properties of materials, especially welded steel materials, to determine the flexibility of the material and the strength of the test material. Bending testing is mostly done to test the bending ability of the welded material. In materials science courses and in materials science laboratories there are no practical teaching aids and bending testing. Therefore, this bending test tool is made very safe for practical demonstrations and testing in the laboratory.
The bending test is one type of material testing carried out to determine the mechanical properties of an engineering material. In practice, there are still few material testing practitioners who pay attention to aspects of the effect of variations in the test object on the bending test results data, and the dimensions that already exist in the ASTM E855-08 standard that we use. For this reason, this bending test tool was made to study the effect of variations in the dimensions of the test object on bending testing. The test is carried out using a hydraulic system bending test equipment. The research method used is three point bending, where the tool in this study is a modified tool from an existing tool. Modification of this tool is carried out on the manometer section for hydraulic pressure, suppression of the test material, and also specimen lift. And the test of the S45C steel test material is one dimensional variation with three trials, namely with a size of 400x40mm and has a thickness of 5mm while the method used in this test is three-point bending.
Data on jack pressure, deviation and time are taken until the specimen/test object gets the maximum pressure and hydraulic compressive force. The test results show that the dimensions of the test object affect the compressive force that occurs during the test. The larger the dimensions tested, the greater the compressive force generated. When performing the bending test, the average value of flexural strength obtained using the three point bending method for 5mm thick steel is 213.5 Mpa, the second test is 228 Mpa, and the third test is 232.1 Mpa.
Keywords: Bending Test, Dimension, Flexural Strength, Three Point Bending