PENGARUH PENGGUNAAN COPPER SLAG SEBAGAI BAHAN PENGISI PASIR PADA CAMPURAN PAVING BLOCK DENGAN MENGGUNAKAN METODE KEPADATAN VOLUME
THE EFFECT OF USING AS A SAND FILLING MATERIAL IN MIXTURE OF PAVING BLOCK USING VOLUME DENSITY METHOD
Pengembangan infrastruktur yang semakin pesat melibatkan penggunaan sumber daya alam yang merupakan bahan baku pembangunan. Pertumbuhan tersebut menyebabkan sumber daya alam semakin menipis sementara pada saat yang sama limbah hasil industri kian meningkat. Oleh karena itu dibutuhkan sebuah inovasi penggunaan bahan non -konvensional dan daur ulang bahan limbah dalam dunia konstruksi. Salah satu pengembangan inovasi tersebut yaitu penggunaan copper slag sebagai substitusi pasir dalam pembuatan paving block. Copper slag merupakan salah satu limbah B3 (Bahan Berbahaya dan Beracun) namun bahan ini dianggap sebagai bahan limbah yang dapat memiliki masa depan yang menjanjikan di industri konstruksi sebagai pengganti sebagian atau keseluruhan dari semen atau agregat.
Tujuan dari penelitian ini yaitu untuk mengetahui pengaruh penggunaan copper slag sebagai bahan pengisi pasir pada campuran paving block terhadap kualitas mutu paving sesuai dengan acuan SNI 03-0691-1996 dengan variasi copper slag 10,5%, 12,5%, 14,5%, 16,5%, dan 18,5%. Presentase copper slag yang digunakan didapat dengan melakukan tes kepadatan volume. Benda uji paving block kemudian diuji kuat tekan, penyerapan air, dan keausan untuk mengetahui kualitas dari paving block yang diteliti. Penelitian ini dilakukan menggunakan metode eksperimen dengan menguji variabel-variabel eksperimen tersebut apakah efektif atau tidak. Pengujian paving block pada penelitian ini dilakukan pada umur 28 hari. Hasil penelitian ini menunjukkan bahwa terdapat pengaruh penambahan copper slag pada pembuatan paving block dimana semakin besar presentase penambahan berbanding lurus dengan berat volume paving. Semakin banyak campuran copper slag yang digunakan, maka semakin tinggi berat volume dan kuat tekan, karena copper slag berfungsi sebagai filler atau menutup pori-pori diantara pasir. Tetapi berbanding terbalik dengan penyerapan air, karena semakin padat dan rapat paving block, maka hasilnya akan rendah. Kualitas terbaik terdapat pada paving block dengan campuran copper slag 10,5% dengan kuat tekan 12, 36 MPa; campuran 12,5% memiliki penyerapan air 7,24%; dan campuran
18,5% yang memiliki keausan 0,1 80 mm/menit.
Kata Kunci: copper slag, paving block, kuat tekan, penyerapan air, dan ketahanan aus .
The rapid development of infrastructure involves the use of natural resources which are the raw materials for development. This growth causes natural resources to be depleted while at the same time industrial waste is increasing. Therefore, we need an innovation in the use of unconventional materials and recycling of waste materials in the construction world. One such innovation development is the use of copper slag as a substitution of sand in the manufacture of paving blocks. Copper slag is one of the B3 wastes (Hazardous and Toxic Material) but this material is considered as a waste material that can have a promising future in the construction industry as a partial or complete replacement of cement or aggregate.
The purpose of this study i s to determine the effect of the use of copper slag as a sand filler in a mixture of paving blocks on the quality of paving quality according to SNI 03 -0691-1996 with copper slag variations of 10.5%, 12.5%, 14.5% , 16.5% and 18.5%. The paving block specimens are then tested for compressive strength, water absorption, and abrasion resistance to determine the quality of the paving blocks studied. This research was conducted using the experimental method by testing the experimental variables whether effective or not. Paving block that used in this study for the testing materials is 28 days maintenance.
The results of this study indicate that there is an effect of the addition of copper slag in the manufacture of paving blocks where the greater percentage of addition is directly proportional to the weight volume of the paving. The more copper used in the mixture, the higher reasult of the volume weight and compressive strength, because the copper slag function’s as a filler or closes the pores between the sand. But it is inversely proportional to the water absorption, because more solid and denser the block is, the result of the water absoption will be low.
The best quality is found in paving mixtures of 10.5% copper slag with a compressive strength of 12,36 MPa; 12.5% mixture has 7,24% water absorption; and 1 8.5% mix which has 0 ,180 mm / minute abrasion resistance.
Kata Kunci: copper slag, paving block, compressive, water absorption,
dan abrasion resistance