ANALISA HASIL PENGELASAN LAS TITIK PADA MESIN SPOTWELDER AND SOLDERING IRON SEMI PORTABLE
ANALYSIS OF WELDING POINT WELDING ON SEMI PORTABLE SPOTWELDER AND SOLDERING IRON MACHINERY
Nama : Riandito Auki Minanda Rahman
NIM : 18050423011
Program Studi : D3 Teknik Mesin
Jurusan : Teknik Mesin
Fakultas : Teknik
Nama Lembaga : Universitas Negeri Surabaya
Pembimbing : Diah Wulandari, S.T., M.T.
Dalam proses manufaktur khususnya pengelasan sebuah benda beberapa kendala yaitu kualitas dari hasil pengelasan dan biaya pembuatan alat tersebut relatif lebih mahal, disamping itu tergantung proses pekerjaan lasnya juga tergantung dari pemilihan parameter pengelasan yang telah ditentukan sehingga hasil yang didapatkan kurang baik. Maka dengan adanya alat ini semoga dapat membantu proses pengelasan karena alat ini relatif lebih murah, efisien, dan memiliki desain yang ringkas dapat dibawa kemana-mana (portable) sekaligus dapat ditempatkan secara menetap (Stationary).
Salah satu cara untuk menganalisa hasil pengelasan adalah dengan melakukan pengujian tarik hasil pengelasan stainless steel dengan tebal 0.6mm, 1mm pada variasi waktu 5detik, 7detik. Setelah mendapatkan hasil pengelasan dilakukan pengujian tarik untuk mengetahui berpengaruh atau tidak variasi waktu dan mengetahui kemampuan maksimum spesimen untuk menahan beban yang bisa disebut “Ultimate Tensile Strength” (UTS) atau disebut tegangan maksimum.
Pada pengujian ini menggunakan mesin Spotwelder and Soldering Iron Semi Portable ini memiliki daya output sebesar 1.107,6 Watt, Ampere sebesar 390, dan tegangan sebesar 2,84 Volt menghasilkan nilai beban tarik maksimal, tegangan tarik dan regangan. Nilai beban tarik maksimal tebal 0,6mm dengan waktu 5detik dan 7detik sebesar 259,80kg dan 213,20kg, sedangkan tebal 1mm sebesar 139kg dan 202kg. Nilai tegangan tarik tebal 0,6mm dengan waktu 5detik dan 7detik sebesar 43,81kg/mm dan 107,68kg/mm, sedangkan tebal 1mm sebesar 78,98kg/mm dan 185,32kg/mm. Nilai regangan tebal 0,6mm dengan waktu 5detik dan 7detik sebesar 8,6% dan 5,7%, sedangkan tebal 1mm sebesar 2,3% dan 3,4%.
Kata Kunci :Las Titik, Hasil Pengelasan, dan Kekuatan Uji Tarik
In the manufacturing process, especially welding an object, there are several obstacles, namely the quality of the welding results and the cost of making the tool is relatively more expensive, besides that, depending on the welding process, it also depends on the selection of welding parameters that have been determined so that the results obtained are not good. So with this tool, hopefully it can help the welding process because this tool is relatively cheaper, efficient, and has a compact design that can be carried everywhere (portable) and can be placed permanently (stationary).
One way to analyze the welding results is to perform tensile testing of stainless steel welding results with a thickness of 0.6mm, 1mm at a time variation of 5 seconds, 7 seconds. After obtaining the welding results, a tensile test is carried out to determine whether or not time variations have an effect and determine the maximum ability of the specimen to withstand loads which can be called "Ultimate Tensile Strength" (UTS) or called maximum stress.
In this test using a Semi Portable Spotwelder and Soldering Iron machine, it has an output power of 1,107.6 Watt, Ampere of 390, and a voltage of 2.84 Volts resulting in a maximum tensile load, tensile stress and strain. The maximum tensile load value is 0.6mm thick with a time of 5 seconds and 7 seconds of 259.80kg and 213.20kg, while the thickness of 1mm is 139kg and 202kg, respectively. The tensile stress value is 0.6mm thick with a time of 5 seconds and 7 seconds of 43.81kg/mm and 107.68kg/mm, while the thickness of 1mm is 78.98kg/mm and 185.32kg/mm. The strain values of 0.6mm thick with a time of 5 seconds and 7 seconds were 8.6% and 5.7%, while the 1mm thickness was 2.3% and 3.4%
Keywords : Spot Welding, Welding Results, and Tensile Test Strength