EXPERIMENTAL STUDY OF THE INFLUENCE OF THE RATIO OF LENGTH OF THE BLADE EDGE ON THE L PLATE WITH THE TURBINE DIAMETER ON THE POWER AND EFFICIENCY OF THE PELTON TURBINE
Meningkatnya kebutuhan energi dari listrik juga ikut menimbulkan masalah yakni ketersediaan energi dari fosil yang sudah sedikit ketersediannya. Degan memanfaatkan sumber energi terbarukan seperti PLTMH diharapkan mampu menggantikan energi yang tidak ramah lingkungan. Turbin Pelton adalah salah satu jenis turbin air yang memanfaatkan potensi ketinggian air (head) dan dengan menggunakan debit air yang kecil sebagai sumber tenaga menggerakkan turbin. Dalam penelitian ini bertujuan untuk mencari rasio terbaik dari panjang ujung sudu pada plat L dengan diameter turbin yang yang mampu menghasilkan daya turbin terbesar dan efisiensi terbaik. Metode yang digunakan dalam penelitian ini yaitu metode eksperimen yang memvariasikan rasio 0, rasio 0.0295, rasio 0.0887 dan rasio 0.1479. Turbin yang digunakan memiliki spesifikasi 8 buah jumlah sudu yang kemudian diuji pada daya muat aliran dari air yang bervariasi yaitu 0.001854, 0.002005, 0.002434, dan 0.003114 dalam satuan m3/s. Turbin ini memiliki 25,4 mm diameter nozzle dan jarak semprot dengan turbin 50 mm diameter. Kemudian juga menggunakan variasi pembebanan untuk memperoleh daya turbin dan efisiensi turbinnya. Diantara variasi rasio pada penelitian ini yang memperoleh daya turbin terbesar yaitu pada rasio 0.0887 pada 0.003114 m3/s daya muat aliran dengan tanggungan yang diberi sebesar 40 kg dan 45.87 Watt dayanya. Efisiensi yang paling optimal juga diperoleh pada rasio 0.0887 saat 0.002005 m3/s daya muat aliran air dan diberi beban sebesar 15 kg bernilai efisiensi sebesar 53,70%. Dapat disimpulkan juga pada rasio 0,0887 menunjukkan hasil paling optimal dengan memperoleh daya dan efisiensi tertinggi pada setiap variasi kapasitas aliran air. Sedangkan turbin berasio 0 memuat daya serta efisiensi turbin terendah dikomparasikan turbin berasio yang lain.
Kata Kunci : Turbin, Pelton, Rasio Panjang Ujung Sudu Plat L dengan Diameter Turbin, Kinerja Turbin Pelton.
The increasing need for energy from electricity also creates problems, namely the availability of energy from fossils which is already in short supply. By utilizing renewable energy sources such as PLTMH, it is hoped that it will be able to replace energy that is not environmentally friendly. The Pelton turbine is a type of water turbine that utilizes the potential water height (head) and uses a small water discharge as a source of power to drive the turbine. In this research, the aim is to find the best ratio of the blade tip length on the L plate to the turbine diameter which is capable of producing the largest turbine power and the best efficiency. The method used in this research is the experimental method which varies the ratio 0, ratio 0.0295, ratio 0.0887 and ratio 0.1479. The turbine used has a specification of 8 blades which are then tested on varying water flow capacities, namely 0.001854, 0.002005, 0.002434, and 0.003114 in m3/s units. This turbine has a nozzle diameter of 25.4 mm and a spray distance from the turbine of 50 mm diameter. Then also use loading variations to obtain turbine power and turbine efficiency. Among the variation of ratios in this study, the one that obtained the largest turbine power was a ratio of 0.0887 at 0.003114 m3/s flow load capacity with a load given of 40 kg and 45.87 Watts of power. The most optimal efficiency is also obtained at a ratio of 0.0887 when 0.002005 m3/s of water flow capacity and given a load of 15 kg has an efficiency of 53.70%. It can also be concluded that the ratio of 0.0887 shows the most optimal results by obtaining the highest power and efficiency for each variation of water flow capacity. Meanwhile, the 0 ratio turbine contains the lowest power and turbine efficiency compared to other ratio turbines.
Keywords: Turbine, Pelton, Ratio of L Plate Blade Tip Length to Turbine Diameter, Pelton Turbine Performance.