ANALISA PEMURNIAN PELUMAS BEKAS HARBOUR MOBILE CRANE DENGAN METODE ACID AND CLAY VARIASI LAMA PENGADUKAN
PURIFICATION ANALYSIS OF HARBOUR MOBILE CRANE USED LUBRICANTS USING ACID AND CLAY METHODS OF DURING VARIATION OF STIRRING
ABSTRAK
Nama : Muhammad Ihza Santoso
NIM : 16050754031
Progam Studi : S-1 Teknik Mesin
Jurusan : Teknik Mesin
Fakultas : Fakultas Teknik
Lembaga : Universitas Negeri Surabaya
Dosen Pembimbing : Dyah Riandadari, S.T., M.T.
Pelumas bekas merupakan limbah B3 karena dapat menyebabkan tanah menjadi tandus dan dapat mencemari perairan karena tidak dapat larut dalam air. Salah satu metode yang digunakan dalam pemurnian pelumas bekas yaitu metode acid and clay. Penelitian ini bertujuan untuk mengetahui karakteristik hasil pemurnian pelumas bekas dengan proses menggunakan asam kuat/acid sebagai pelarut dan clay.
Penelitian ini merupakan eksperimen pelumas bekas harbour mobile crane sebagai objek dalam pemurnian pelumas bekas. Pada penelitian ini adsorben yang digunakan adalah bentonit dan asam kuat menggunakan asam sulfat (H₂SO₄) dengan memvariasikan lama pengadukan bentonit yaitu (3, 4, 5 jam) dan (900, 1000, 1100 rpm). Suhu adsorpsi 70 ºC.
Hasil yang diperoleh yaitu perubahan viskositas kinematik tertinggi untuk suhu 40°C adalah pada variasi 5 jam 1000 rpm yaitu 106,96 cSt, sedangkan untuk suhu 100°C adalah pada variasi 4 jam 1000 rpm yaitu 8,878 cSt. Hasil optimal Flash Point didapat pada lama pengadukan 4 jam 1000 rpm yaitu 212°C. Hasil optimal Density didapat pada kondisi lama pengadukan 3 jam 1000 rpm dengan hasil 0,8845.
Kata kunci : pelumas, pemurnian pelumas, metode acid and clay, bentonit, variasi waktu pengadukan.
ABSTRACT
PURIFICATION ANALYSIS OF HARBOR MOBILE CRANE USED LUBRICANTS USING ACID AND CLAY METHODS OF DURING VARIATION OF STIRRING
Name : Muhammad Ihza Santoso
ID Number : 16050754031
Study Program : S-1 Mechanical Engineering
Department : Mechanical Engineering
Faculty : Faculty Of Engineering
Institution : State University of Surabaya
Supervisor : Dyah Riandadari, ST, MT
Used lubricant is B3 waste because it can cause the soil to become barrenand can pollute the waters because they are insoluble in water. One of the methods used in the purification of used lubricants is the acid and clay method. This study aims to determine the characteristics of the refined lubricants used with the acid and clay method, which is a process using strong acid as a solvent and clay.
This research is an experiment of used lubricants from harbour mobile cranes as an object in refining used lubricants. In this study, the adsorbent used was bentonite and strong acid using sulfuric acid (H₂SO₄) by varying the length of stirring the bentonite, namely (3, 4, 5 hours) and (900, 1000, 1100 rpm). Adsorption temperature 70 ºC.
The results obtained are the highest kinematic viscosity change for a temperature of 40 ° C is at a variation of 5 hours 1000 rpm which is 106.96 cSt, while for a temperature of 100 ° C is at a variation of 4 hours 1000 rpm which is 8.878 cSt. The optimal results of Flash Point were obtained at 4 hours stirring time of 1000 rpm, which is 212 ° C. The optimal density results were obtained at the stirring time of 3 hours 1000 rpm which is 0.8845.
Keywords : lubricants, lubricant purification, acid and clay method, bentonite, variation of stirring time.