UTILIZATION OF LDPE (LOW DENSITY POLYETHYLENE) PLASTIC WASTE AS AN ALTERNATIVE FUEL THROUGH THE PYROLYSIS PROCESS
Penduduk manusia yang semakin meningkat sangat berpengaruh terhadap meningkatnya produksi dan penggunaan plastik yang dihasilkan sangat berpengaruh besar dalam pencemaran. Sehingga, pengolahan limbah plastik dapat dilakukan dengan mendaur ulang sampah plastik menjadi bahan bakar alternatif dengan melalui proses pirolisis. Tujuan dari penelitian adalah untuk menganalisis karakterisitik variasi temperatur di reaktor pembakaran terhadap densitas, viskositas,nilai kalor, dan flashpoint, serta menganalisis hasil minyak dari proses pirolisis dengan menggunakan bahan baku limbah dari plastik ber-jenis Low Density Polyethylene (LDPE). Penelitian ini menerapkan metode eksperimen dengan variasi temperatur reaktor 275°C, 300°C, dan 350°C. Jenis bahan yang digunakan limbah plastik berjenis Low Density Polyethylene (LDPE). Pengujian karakteristik bahan bakar menggunakan standar ASTM (densitas D1298, viskositas D1343, flash point D93). Penelitian dilaksanakan di Laboratorium Bahan Bakar dan Pelumas, Fakultas Teknik, Universitas Negeri Surabaya. Analisa data dilakukan dengan jenis analisa deskriptif kuantitatif. Hasil dari penelitian menunjukkan bahwa proses pirolisis jenis plastik Low Density Polethylene (LDPE) yang menghasilkan karakteristik nilai densitas yang mencapai setara dengan pertalite dengan temperatur 300°C dan 350°C memperoleh 0,76 kg/l dan 0,782 kg/l. Nilai viskositas pada temperatur 275°C serupa dengan minyak tanah memperoleh 2,8 cst. Pada nilai kalor dengan temperatur 300°C dan 350°C serupa dengan pertalite memperoleh 10956 cal/g dan 11107 cal/g. Titik nyala dari nilai flash point pirolisis berada diatas flash point pertalite. Dari hasil yang didapat nilai flash point dan viskositas dapat disimpulkan bahwa karakteristik minyak pirolisis LDPE (Low Density Polyethyelene) termasuk jenis bahan bakar like minyak tanah dengan temperatur reaktor 275°C.
The growing human population has significantly impacted the production and use of plastic, which significantly contributes to pollution. Therefore, plastic waste can be processed by recycling it into alternative fuels through the pyrolysis process. The objectives of this research were to analyze the characteristics of temperature variations in a combustion reactor on density, viscosity, calorific value, and flash point, and to analyze oil yield from the pyrolysis process using Low Density Polyethylene (LDPE) plastic waste as raw material. This research used an experimental method with reactor temperatures varying from 275°C, 300°C, and 350°C. The type of plastic waste used was Low Density Polyethylene (LDPE). Fuel characteristics were tested using ASTM standards (density D1298, viscosity D1343, flash point D93). The research was conducted at the Fuels and Lubricants Laboratory, Faculty of Engineering, Surabaya State University. Data analysis was conducted using quantitave descriptive analysis. The results of the study indicate that the pyrolysis process of Low Density Polyethylene (LDPE) plastic produces characteristics of density values that are equivalent to pertalite with temperatures of 300°C and 350°C obtaining 0.76 kg/l and 0.782 kg/l. The viscosity value at a temperature of 275°C is similar to kerosene obtaining 2.8 cst. At a calorific value with a temperature of 300°C and 350°C similar to pertalite obtaining 10956 cal/g and 11107 cal/g. The flash point of the pyrolysis flash point value is above the pertalite flash point. From the results obtained, it can be concluded that the characteristics of LDPE (Low Density Polyethylene) including a type of fuel like kerosene with a reactor temperature of 275°C.